Cabinet-housed speakers


DPS 26 - 100 V



dps26_1

26 x 26 cm dipole flat-panel loudspeaker made of corrosion resistant aluminum with weatherproof equipment for outdoor use. The DPS 26 is a passive speaker without power supply, adapted for all applications of speech reproduction (e.g. announcements at railway stations, etc.). The optimized directivity pattern and focused sound radiation ensure perfect speech intelligibility while minimizing the disturbance of nearby areas (noise pollution). The clear design line with a square body, simple and variable mounting possibilities as well as thoughtful power taps on the 100 V transformer for easier adjustment complete the advantages.


Connection (100 V)

+ / -

Red / White

6 W

White / Yellow

3 W

Yellow / Black

1.5 W
Red / Yellow 1 W
White / Black 0.5 W
Red / Black 0.3 W

DPS 40 EN - 100 V



dps40en_9006

The DPS 40 EN dipole flat-panel loudspeaker has been specifically developed to deal with particularly critical acoustic characteristics in rooms with high reverberation levels. In contrast to the similar model DPS 40 F - 100 V, the loudspeakers of DPS 40 EN are arranged as a symmetrical array. The sound is sharply focused both in horizontal and vertical directions therefore. Because this loudspeaker is normally installed on a higher place (bottom edge about 3 m), there is a passive time delay element integrated to optimize the radiating direction at an angle of -10°. DPS 40 EN is a passive loudspeaker, so it will not require any power supply.


Railway station PA speakers

A key objective of public address systems in railway stations is to ensure that every message relating to railway operation and in emergencies is clearly audible to all travellers at the target location in the station. DIN EN 60268-16 sets ambitious standards for speech intelligibility because the acoustic environment on railway platforms is a difficult one.

  • Trains arriving and leaving generate very loud ambient noises and require the loudspeakers to have a correspondingly high loudness level
  • Announcements on adjacent platforms make other announcements unintelligible unless the sound is properly and effectively restricted to the required target area 
  • Sound reverberating from the sound-reflecting ceilings and walls in enclosed station buildings generates interference noise that makes the announcement hard to understand.

The passive train station loudspeakers made by VISATON will, however, allow the required speech intelligibility to be achieved, despite the difficult surroundings. These speakers are dipole flat-panel speakers, and provide the required high levels of sound pressure while focussing the sound they produce more accurately than classic speaker systems.

A dipole speaker works by creating air movement (as sound pressure waves) directly from the front and back surfaces of the driver, while the amount of sound emitted to the sides, up and down is much reduced. An arrangement of several loudspeakers in line or in a single plane results in an even more closely focussed sound image. By combining these two principles, VISATON has achieved a targeted improvement in the polar characteristics of loudspeaker systems.

Thanks to this principle, the platform in front of and behind the loudspeaker is addressed and the adjacent platforms hardly hear any of it. The sound also hardly reaches the ceiling and floor so interfering reverberations that would reduce speech intelligibility are reduced.


Connection (100 V)

+ / -

Red / White

40 W

White / Yellow

20 W

Yellow / Black

10 W

Red / Yellow

6.9 W

White / Black

3.4 W

DPS 40 F - 100 V (RAL 5022)



dps40f_5022

The DPS 40 F - 100 V dipole flat-panel loudspeaker has been developed and optimised specifically for applications in the open-air with limited adjoining reflecting surfaces (such as ceilings). It focuses the sound to a great extent in a horizontal direction, so neighbours or adjacent station platforms only receive much reduced signals than would be the case with classic horn speakers. Sound field simulations coupled with measurements under real-life field conditions demonstrate that there is a difference in the level of interference noise to the sides of the platform of 6 to 8 dB in favour of dipole flat-panel speakers. At the same time, their efficiency is considerably higher, which means that typical horn speakers would require eight times the amplifier output to achieve the same sound pressure on a railway platform.

Versions: Models with one side closed e.g. for use at the ends of platforms.

  • DPS 40 F-GR - 100 V (closed at the right side)
  • DPS 40 F-GL - 100 V (closed at the left side)


Railway station PA speakers

A key objective of public address systems in railway stations is to ensure that every message relating to railway operation and in emergencies is clearly audible to all travellers at the target location in the station. DIN EN 60268-16 sets ambitious standards for speech intelligibility because the acoustic environment on railway platforms is a difficult one.

  • Trains arriving and leaving generate very loud ambient noises and require the loudspeakers to have a correspondingly high loudness level
  • Announcements on adjacent platforms make other announcements unintelligible unless the sound is properly and effectively restricted to the required target area
  • Sound reverberating from the sound-reflecting ceilings and walls in enclosed station buildings generates interference noise that makes the announcement hard to understand.

The passive train station loudspeakers made by VISATON will, however, allow the required speech intelligibility to be achieved, despite the difficult surroundings. These speakers are dipole flat-panel speakers, and provide the required high levels of sound pressure while focussing the sound they produce more accurately than classic speaker systems.

A dipole speaker works by creating air movement (as sound pressure waves) directly from the front and back surfaces of the driver, while the amount of sound emitted to the sides, up and down is much reduced. An arrangement of several loudspeakers in line or in a single plane results in an even more closely focussed sound image. By combining these two principles, VISATON has achieved a targeted improvement in the polar characteristics of loudspeaker systems.

Thanks to this principle, the platform in front of and behind the loudspeaker is addressed and the adjacent platforms hardly hear any of it. The sound also hardly reaches the ceiling and floor so interfering reverberations that would reduce speech intelligibility are reduced.



Connection (100 V)

+ / -

Red / Black

10 W

Yellow / Black

6 W

White / Black

3 W

KL 13 - 100 V



kl13

Aesthetically appealing spherical loudspeaker with a 13 cm full-range speaker system. Very efficient system, good voice reproduction and a pleasing overall sound quality. Connection to 100 V and 70 V supplies and amplifier with 4 or 8 ohm outputs possible.

KL 33 - 100 V (white)



kl33_ws

33 cm spherical loudspeaker as bass reflex system. Equipped with one 17 cm bass/midrange and four midrange/highrange drivers which have a good directivity pattern at off-axis angles and therefore provide a uniform and pleasant sound quality. The KL 33 can be connected to a 100 V network or a normal amplifier (4 ohm).

PL 13 - 100 V



pl13

Projection loudspeaker with cylindrical plastic housing (ABS) and adjustable fixing bracket. Suitable for wall or ceiling mounting. Fitted with one full-range loudspeaker and 100 V transformer. High level of voice quality.

PL 13 BS - 100 V



pl13bs

Projection loudspeaker with cylindrical plastic housing (ABS) and adjustable fixing bracket. Suitable for wall or ceiling mounting. High level of voice quality. Fitted with one fullrange loudspeaker, 100 V transformer, ceramic terminal and a thermal fuse. Conforms to both Dutch (NEN 2575) and British (BS 5839) regulations for alarm systems. Prepared to insert fire-proof cabling with a cable connexion.

PL 13 D - 100 V



pl13d

Twin radiating loudspeaker with cylindrical plastic housing (ABS) and sturdy mounting bracket (aluminium). Fitted with two full range loudspeakers and 100 V transformer. Cables can be concealed in the bracket if required. High level of voice quality. Particularly suitable for corridors and other elongated rooms.

PL 13 DBS - 100 V



pl13d

Twin radiating loudspeaker with cylindrical plastic housing (ABS) and sturdy mounting bracket (aluminium). Fitted with two full range loudspeakers and 100 V transformer, ceramic terminal and a thermal fuse. Conforms to both Dutch (NEN 2575) and British (BS 5839) regulations for alarm systems. Prepared to insert fire-proof cabling with a cable connexion. Cables can be concealed in the bracket if required. High level of voice quality. Particularly suitable for corridors and other elongated rooms.

PL 5 RV - 4 Ohm



pl5rv_1

4 cm (1,6“) fullrange speaker with a small housing and threaded mounting ring for easy installation for example in dash boards. High efficiency at frequencies relecant for speech reproduction, increased power handling through high pass filter. 1 m cable.

PL 7 RV - 4 Ohm



pl7rv_4_1

7 cm (2.5") flush-mounted speaker with a threaded mounting ring at the plastic housing for easy installation in round openings without additional screws. High efficiency at frequencies relevant for speech reproduction. Including 50 cm cable. 

PL 7 RV - 4 Ohm (NCS S 3000-N)



pl7rv_4_ncss3000n_1

7 cm (2.5") flush-mounted speaker with a threaded mounting ring at the plastic housing for easy installation in round openings without additional screws. High efficiency at frequencies relevant for speech reproduction. Including 50 cm cable. 

PL 7 RV - 8 Ohm



pl7rv_4_1

7 cm (2.5") flush-mounted speaker with a threaded mounting ring at the plastic housing for easy installation in round openings without additional screws. High efficiency at frequencies relevant for speech reproduction. Including 50 cm cable. 

SUB CP 130 S - 16 Ohm



sub_cp130s

Compound Subwoofer with two W 130 S - 8 Ohm woofers for powerful bass at compact outer dimensions. Cabinet made of MDF with 9 l net volume. The two 8 ohms woofers are connected in serial to 16 ohms to allow a simple parallel connection of up to 4 subwoofers.

UL 7 N - 100 V



ul7n

Cabinet-housed speaker for use in lighting systems. Stainless steel cabinet (V2A). Equipped with two 7 cm fullrange speakers and an 100 V transformer.

WB 10 - 100 V/8 Ohm (black)



wb10_sw_1

2-way compact speakers in a sturdy plastic housing (black), fitted with one 10 cm woofer and one tweeter providing broad frequency response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required.

WB 10 - 100 V/8 Ohm (white)



wb10_ws_1

2-way compact speakers in a sturdy plastic housing (black), fitted with one 10 cm woofer and one tweeter providing broad frequency response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required.

WB 13 - 100 V/8 Ohm (black)



wb13_sw

2-way compact speakers in a sturdy plastic housing (black), fitted with one 13 cm woofer and one tweeter providing broad frequency response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required, and the housing is equipped with a threaded hole for attaching to a bracket or swivelling arm.

WB 13 - 100 V/8 Ohm (white)



wb13_ws

2-way compact speakers in a sturdy plastic housing (white), fitted with one 13 cm woofer and one tweeter providing broad frequency response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required, and the housing is equipped with a threaded hole for attaching to a bracket or swivelling arm.

WB 16 - 100 V/8 Ohm (black)



wb16_sw

2-way compact speakers in a sturdy plastic housing (black), fitted with one 16 cm woofer and one tweeter providing broad frequenc response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required, and the housing is equipped with a threaded hole for attaching to a bracket or swivelling arm.

WB 16 - 100 V/8 Ohm (white)



wb16_ws

2-way compact speakers in a sturdy plastic housing (white), fitted with one 16 cm woofer and one tweeter providing broad frequency response. Well suited for music and voices. Universally applicable to professional PA or in the home. Can be run as a 100 V system or as 8 ohm units due to an integrated transformer. 100 V transformer and 8 ohm mode are selected using a knob. Swivelling fixing bracket allows the speakers to be mounted horizontally or vertically, as required, and the housing is equipped with a threaded hole for attaching to a bracket or swivelling arm.

WL 10 P - 100 V



wl10p_1

Waterproof cabinet speaker with 100 V transformer. Robust white plastic cabinet with integrated protective grille. Different transformer tappings for the 100 V network level adjustment. High efficiency, wide frequency range with clear high-range for good speech intelligibility. Suitable for background music as well. Equipped with ceramic terminal and thermal fuse.

WL 13 N - 100 V



wl13n

Wall-mounted speaker with a wooden cabinet and metal grille. Fitted with a high quality full range driver. Removable rear panel for easy fitting to the wall using two screws. Good music reproduction and clear speech reproduction properties. Connection to 100 V network and level trimming by means of spring terminal.

Also available:
- WL 13 NR - 100 V (with volume cotrol)

WL 13 NR - 100 V



wl13nr_nrp

Wall-mounted speaker with a volume control-knob, wooden cabinet and metal grille. Fitted with a high quality full range driver. Removable rear panel for easy fitting to the wall using two screws. Good music reproduction and clear speech reproduction properties. Connection to 100 V network and level trimming by means of spring terminal.

Also available:
- WL 13 N - 100 V (without volume cotrol)

WL 13 P - 100 V



wl13p

Wall-mounted speaker with a white plastic cabinet and metal grille. Fitted with a full range driver. Good music reproduction and clear speech reproduction properties. Connection to 100 volt network and level trimming by means of spring terminal.

Also available:
WL 13 PR - 100 V (with volume cotrol)

WL 13 PR - 100 V



wl13pr

Wall-mounted speaker with a volume control-knob, white plastic cabinet and metal grille. Fitted with a full range driver. Good music reproduction and clear speech reproduction properties. Connection to 100 volt network and level trimming by means of spring terminal.

Also available:
WL 13 P - 100 V (without volume cotrol)

WL 21.33 - 100 V



wl21_33

Wall-mounted speaker with a white plastic cabinet and metal grille. Fitted with a full range driver, a 100 V transformer and a fire-proof ceramic terminal with thermal fuse (fire damage at the speaker does not affect the function of the entire system). Very high efficiency, clear speech reproduction properties.

 

WL 25.20 AB EV - 100 V



wl25_20abev_1

Wall-mounted speaker with a white plastic cabinet and metal grille. Fitted with two full range drivers and two 100 V transformers for space saving A/B connection according to DIN EN 60849/VDE 0828 and VDE 0833-4. Clear speech reproduction properties. Connection to the 100 volt network and level trimming by means of screw terminals.

WL 25.20 EV - 100 V



wl25_20ev_1

Wall-mounted speaker with a white plastic cabinet and metal grille. Fitted with a full range driver and a 100 V transformer. Clear speech reproduction properties. Connection to the 100 volt network and level trimming by means of screw terminal.